Home \ Browse Journal \ 2025 \ 2025 Volume 8 Issues 1–3 \ Electrorheological Response of a Suspension Based on a Silicone Oil and Chitosan-Modified Graphene Oxide

2025 Volume 8 Issues 1–3

инэос-open
Open Access
cc-by-nc

INEOS OPEN, 2025, 8 (1–3), 149–150

Journal of Nesmeyanov Institute of Organoelement Compounds
of the Russian Academy of Sciences

Download PDF
DOI: 10.32931/io2558a

issue_cover_8_1-3.png       

Electrorheological Response of a Suspension Based on a Silicone Oil
and Chitosan-Modified Graphene Oxide

P. A. Vovkotrub, D. Yu. Stolyarova,* and S. N. Chvalun

National Research Center "Kurchatov Institute", pl. Akademika Kurchatova 1, Moscow, 123182 Russia
 

Corresponding author: D. Yu. Stolyarova, e-mail: stolyarova_dy@nrcki.ru
Received 5 November 2024; accepted 11 March 2025

Abstract

io2558a_abs_fig

A highly efficient low-concentration electrorheological fluid, namely, a smart suspension that changes its rheological properties in an external electric field was obtained and studied. A silicone oil was chosen as a dispersion medium, which was filled with a synthesized stimuli-sensitive composite of graphene oxide (GO) modified with chitosan. The electrorheological tests showed that the resulting suspension has a pronounced response: the yield point reached 1.12 kPa at a field strength of 7 kV/mm.

Key words: composite, graphene, chitosan, electrorheological effect.

 

Introduction

The electrorheological (ER) effect discovered by Winslow in 1949 [1] in colloidal systems where the medium and filler have different permittivity determined the emergence of new technologies in the field of oil transportation, food industry, robotics, and microfluidics [2–4]. ER fluids are most prevalent. Electrorheological fluids can change their viscoelastic properties in an external electric field, which allows for attributing them to smart soft materials. Nowadays, many research efforts are focused on finding the most effective fillers for ER systems. The composites based on chitosan [5] and different modifications of graphene [6] have long been of particular interest; however, these components are capable of exhibiting a synergistic effect, as is shown in this work.

Results and discussion

The structuring of particles under the influence of an external electric field (EF) was visualized by optical microscopy. Figure 1a shows a micrograph of the suspension changes when an EF is applied. It can be seen that initially the composite particles are randomly distributed in the dispersion medium. When a field of 1 kV/mm is applied, the particles are oriented along the lines of force with the formation of reinforcing structures (Fig. 1b), which clearly demonstrates the presence of the ER effect in the sample under consideration.

io2558a_fig1

Figure 1. Optical micrographs of the suspension in the absence of an external EF (a) and upon its application (b).

To determine the magnitude of the ER response to the applied field, the electrorheological tests were carried out for the suspension samples of all obtained concentrations and unfilled PDMS. Figure 2 presents the yield points upon application of an EF from 1 to 7 kV/mm. The data were obtained by approximating the flow curves according to the Bingham model.

io2558a_fig2

Figure 2. Dependence of the static yield strength on the EF stress for the suspensions of the GO–chitosan composite
with the concentrations of 0.25, 0.50, and 0.75 wt % and unfilled PDMS.

As can be seen from Fig. 2, when an electric field is applied, all samples develop yield points which increase with the increasing EF strength. An increase in the concentration of particles in the suspension also affects the magnitude of the ER response: the yield strength increases with an increase in the system filling degree. This can be explained by the fact that, with an increase in the suspension concentration, the filler particles are in closer contact with each other, which simplifies the formation of a reinforcing network. The highest yield point was observed for the sample with a filler concentration of 0.75 wt % at 7 kV/mm and reached 1.122 kPa. For the samples with the concentrations of 0.25 and 0.50 wt % at 7 kV/mm, the yield points were 0.356 kPa and 0.519 kPa, respectively.

Experimental section

Methods

The structures of the resulting suspensions were studied in the absence and upon application of an electric field using an Axio Imager.M2m optical polarization microscope (Carl Zeiss, Sweden). The electric potential was applied from an IVNR-15/1(+/–) high-voltage source (Plazon, Russia), the operating range of the applied voltage was 0–4 kV. The rheological behavior of the suspensions was studied by coaxial cylinder rotational viscometry using a Physica MCR 501 rheometer (Anton Paar, Germany). The cell volume was 20 mL, the gap was 1 mm. The electric field strength was varied from 0 to 7 kV/mm. The potential was supplied from an HCP 14–12500 MOD (FuG Elektronik, Germany) external high-voltage source.

Preparation of materials and synthesis

The filler, GO, was obtained in the Laboratory of Functional Polymeric Systems and Composites (Semenov Federal Research Center of Chemical Physics, Russian Academy of Sciences) in the form of an aqueous suspension with a particle concentration of 1.5 wt %. The modifying agent was low-molecular chitosan ChitoClear 43000–HQG 10 (Primex, Iceland) (Mn = 70 kDa, DD = 75%). The dispersion medium was a silicone oil with a dynamic viscosity of 0.107 Pa·s (PMS-100, GOST (State Standard) 13032-77, Penta Yunior, Russia).

The suspension of the GO–chitosan composite was obtained according to the published procedure [7]. To remove the solvent, the suspension was frozen and lyophilized using a Martin Christ Alpha 2-4LSC installation. The resulting GO–chitosan composite aerogel was dispersed in the silicone oil to obtain homogeneous suspensions with a filler concentration of 0.25, 0.50, and 0.75 wt %.

Conclusions

The GO–chitosan composite was synthesized and its suspensions with the concentrations of 0.25, 0.50 and 0.75 wt % were obtained. The ER characteristics of the resulting systems were elucidated. The optical and electrorheological tests revealed that all the samples represent ER fluids. In an electric field, the particles are polarized and form a reinforcing structure, which leads to the appearance of yield points and their subsequent growth, depending on the magnitude of the applied field and the filling degree of the system. It should be noted that even at low concentrations of the filler (<1 wt %), the fluids displayed a high ER response; therewith, up to a field strength of 7 kV/mm, the leakage current in the systems did not exceed 1 mA. The maximum yield point was detected for the suspension with a concentration of 0.75 wt % at 7 kV/mm and reached 1.122 kPa.

Acknowledgements

This work was supported by the state task of NRC "Kurchatov Institute".

References

  1. W. M. Winslow, J. Appl. Phys., 1949, 20, 1137–1140. DOI: 10.1063/1.1698285
  2. R. Tao, E. Du, H. Tang, X. Xu, Fuel, 2014, 134, 493–498. DOI: 10.1016/j.fuel.2014.06.018
  3. R. Tao, H. Tang, K. Tawhid-Al-Islam, E. Du, J. Kim, PNAS, 2016, 113, 7399–7402. DOI: 10.1073/pnas.1605416113
  4. Y. Liang, D. Huang, X. Zhou, Z. Wang, Q. Shi, Y. Hong, H. Pu, M. Zhang, J. Wu, W. Wen, Engineering, 2023, 24, 151–171. DOI: 10.1016/j.eng.2022.01.014
  5. Y. G. Ko, U. S. Choi, B. H. Sung, J. Appl. Polym. Sci., 2004, 93, 1559–1566. DOI: 10.1002/app.20632
  6. M. V. Gudkov, D. Yu. Stolyarova, K. A. Shiyanova, V. P. Mel'nikov, Polym. Sci., Ser. C, 2022, 64, 40–61. DOI: 10.1134/S1811238222010027
  7. H. Bao, Y. Pan, Y. Ping, N. G. Sahoo, T. Wu, L. Li, J. Liu, L. H. Gan, Small, 2011, 7, 1569–1578. DOI: 10.1002/smll.201100191