Home \ Browse Journal \ 2025 \ 2025 Volume 8 Issues 1–3 \ Synthesis of Wide Bandgap Conjugated π-Copolymers Incorporating 9H-Carbazol-3-yl Dithieno[3,2-f:2',3'-h]quinoxaline Units

2025 Volume 8 Issues 1–3

инэос-open
Open Access
cc-by-nc

INEOS OPEN, 2025, 8 (1–3), 20–21 

Journal of Nesmeyanov Institute of Organoelement Compounds
of the Russian Academy of Sciences

Download PDF
Electronic supplementary information
DOI: 10.32931/io2507a

issue_cover_8_1-3.png       

Synthesis of Wide Bandgap Conjugated π-Copolymers Incorporating
9H-Carbazol-3-yl Dithieno[3,2-f:2',3'-h]quinoxaline Units

M. L. Keshtov,a N. K. Davydova,a D. P. Kalinkin,*a and G. D. Sharmab

a Nesmeyanov Institute of Organoelement Compounds, Russian Academy of Sciences, ul. Vavilova 28, str. 1, Moscow, 119334 Russia
b St. Department of Physics and Electronics Communication Engineering, LNM Institute for Information Technology, Jamdoli, Jaipur, Raj., 302031 India

 

Corresponding author: D. P. Kalinkin, e-mail: kalinkin@ineos.ac.ru
Received 23 September 2024; accepted 15 October 2024

Abstract

S S N N N N C 8 H 17 C 10 H 21 C 8 H 17 C 10 H 21 * S S S * S O O C 8 H 17 C 8 H 17 n  

A new wide bandgap material, P1, was synthesized and compared by the optical and electrochemical properties with the well-known copolymer PM6. Upon employing the narrow bandgap non-fullerene acceptor Y6, the organic solar cells based on P1 and PM6 under identical processing conditions exhibited overall power conversion efficiencies of 13.48 and 14.81%, respectively. Utilizing P1 as the secondary donor led to the optimized ternary organic solar cell with a power conversion efficiency of 17.11%, exceeding that of the binary counterparts.

Key words: synthesis, copolymer, organic solar cell, photovoltaic application.

 

Introduction

Currently, the majority of π-conjugated polymers utilized in polymer solar cells (PSCs) are predominantly produced by the polycondensation method using the Stille cross-coupling [1]. However, this approach presents various challenges, such as the preliminary multi-step synthesis of aryl tin reactants and the production of harmful by-products. To overcome these challenges, the idea of utilizing a novel polycondensation process through direct arylation has emerged as an attractive and environmentally friendly alternative to the traditional coupling reactions. This approach eliminates the need for stannyl derivatives and the requirement for organometallic reagents, leading to a reduction in the synthesis steps and costs. Given the significant interest in conjugated polymers containing quinoxaline (Qx) units [2–4], there is a push for further enhancements towards simpler, quicker, and more cost-effective synthetic approaches. However, the development of Qx-conjugated polymers via direct polycondensation remains exceedingly scarce and poorly understood [5]. To address the challenges mentioned above, this study undertook the synthesis of a novel π-conjugated Qx-containing polymer P1 through a direct heteroaryl polycondensation reaction.

Results and discussion

In this study, we developed and synthesized a monomer, M1, and utilized it to obtain a new π-conjugated polymer, P1, through the direct heteroarylation procedure (Scheme 1).

S S N N N N C 8 H 17 C 10 H 21 C 8 H 17 C 10 H 21 S S N N N N C 8 H 17 C 10 H 21 C 8 H 17 C 10 H 21 * S S S Br Br S O O C 2 H 5 C 2 H 5 C 4 H 9 C 4 H 9 S S S * S O O C 8 H 17 C 8 H 17 n P 1 M 1 H H M2 Pd 2 (dba) 3 K 2 CO 3 /PivOH toluene 100 o C, 20 h  

Scheme 1. Synthetic route to copolymer P1.

The resulting copolymer P1 is soluble in common organic solvents, such as chloroform (CF) and chlorobenzene, with a number average molecular weight (Mn) of 20.1 kDa and a polydispersity index (PDI) of 2.40 (Table S1 in the Electronic supplementary information (ESI)). The high value of Mn and the low PDI of P1 support enhanced charge transport characteristics. The thermal gravimetric analysis (TGA) revealed a decomposition temperature (Td) of 358 °C for P1, indicating its suitability for use in fabricating organic photoelectronic devices. The absorption spectra of P1 in CF and thin film as well as those of PM6 [6] and Y6 [7] thin films are depicted in Fig. 1. The absorption spectrum of P1 in thin film exhibits a significant red shift compared to the spectrum in solution, with the primary absorption peak located at 427 nm. This observation suggests the presence of a more ordered structure and π–π stacking interactions in the solid state, contributing to enhanced charge mobility of the polymer in this state. Finally, the optical band gap (Egopt) of wide-band P1 is determined to be 2.06 eV.

io2507a_fig1

Figure 1. Absorption spectra of P1 in СF and P1, PM6, Y6 in thin film.

We fabricated the bulk heterojunction (BHJ) organic solar cells (OSCs) (ITO/PEDOT:PSS/BHJ active layer/PFN-Br/Al), using P1 as the donor and Y6 as the acceptor and evaluated their photovoltaic performance in comparison to the PM6 donor under identical processing conditions. The optimized active layer was subjected to solvent vapor annealing by exposing it to tetrahydrofuran (THF) vapors for 40 s. The J–V characteristics of the optimized OSCs are presented in Table 1.

Table 1. Photovoltaic parameters of the optimized binary and ternary OSCs

Device
JSC, [mA/cm2]
VOC, [V]
FF
PCE, [%]
P1:Y6
21.54 (21.29)a
0.957
0.654
13.48 (13.23)b
PM6:Y6
24.62 (24.39)a
0.840
0.716
14.81 (14.54)b
PM6:P1:Y6
25.74 (25.52)a
0.908
0.732
17.11 (16.87)b
a estimated from the integration of external quantum efficiency (EQE) spectra;
b average of eight identical devices; JSC is the short circuit current; VOC is the open circuit voltage; FF is the fill factor; PCE is the power conversion efficiency.

The optimized OSCs based on PM6:Y6 and P1:Y6 achieved PCEs of 13.48 and 14.81%, respectively. The value of VOC of P1-based OSCs (0.957 V) surpassed that of its PM6 counterpart (0.84 V) due to a deeper highest occupied molecular orbital (HOMO) energy level of P1 relative to PM6. This variation in the values of VOC for the active layer-based OSCs reflects the energy difference between the acceptor lowest unoccupied molecular orbital (LUMO) and the donor HOMO. The higher value of JSC for the PM6-based OSCs, in contrast to P1, arises from the efficient dissociation of excitons at the PM6/Y6 interfaces, substantiated by the more effective photoluminescence (PL) quenching of Y6 for Y6:PM6 relative to Y6:P1. The optimized ternary OSC exhibits a PCE of approximately 17.11%, surpassing that of its binary counterparts owing to the increased JSC and FF values.

Conclusions

We developed a new donor-acceptor (D-A) copolymer, P1, which demonstrates a deeper HOMO level and a larger dipole moment compared to PM6. Although the optimized P1:Y6 active layer-based OSCs exhibited a PCE of 13.38%, lower than that of the PM6 counterpart (14.81%), the P1-based OSC showcased a higher value of VOC, attributed to its deeper HOMO energy level. Leveraging the higher VOC for the P1-based device and the complementary absorption spectra of P1 and PM6, the ternary OSC based on the P1:PM6:Y6 (0.2:0.8:1.2) active layer achieved an overall PCE of 17.11%, surpassing that for binary counterparts. An increase in the values of JSC and FF for the ternary OSC is attributed to the higher exciton generation and their more effective dissociation into free charge carriers owing to the appropriate phase separation and morphology of the ternary active layer.

Acknowledgements

This work was supported by the Russian Science Foundation (project no. 24-43-02039).

The spectral characterization, NMR and X-ray diffraction studies were performed using the equipment of the Center for Molecular Composition Studies of INEOS RAS with financial support from the Ministry of Science and Higher Education of the Russian Federation.

Electronic supplementary information

Electronic supplementary information (ESI) available online: the experimental section, NMR spectra, cyclic voltammograms, molecular weights and thermal properties of P1, as well as the details of the device fabrication. For ESI, see DOI: 10.32931/io2507a.

References

  1. B. Carsten, F. He, H. J. Son, T. Xu, L. Yu, Chem. Rev., 2011, 111, 1493–1528. DOI: 10.1021/cr100320w
  2. Y. Xu, Y. Cui, H. Yao, T. Zhang, J. Zhang, L. Ma, J. Wang, Z. Wei, J. Hou, Adv. Mater., 2021, 33, 2101090. DOI: 10.1002/adma.202101090
  3. M. R. Busireddy, T.-W. Chen, S.-C. Huang, H. Nie, Y.-J. Su, C.-T. Chuang, P.-J. Kuo, J.-T. Chen, C.-S. Hsu, ACS Appl. Mater. Interfaces, 2022, 14, 22353–22362. DOI: 10.1021/acsami.2c04104
  4. S. Jung, S. Jeong, J. Oh, S. Kim, S. Lee, S.-J. Yoon, C. Yang, Chem. Commun., 2023, 59, 1991–1994. DOI: 10.1039/D2CC06725K
  5. A. Efrem, K. Wang, P. N. Amaniampong, C. Yang, S. Gupta, H. Bohra, S. H. Mushrif, M. Wang, Polym. Chem., 2016, 7, 4862–4866. DOI: 10.1039/C6PY00719H
  6. M. Zhang, X. Guo, W. Ma, H. Ade, J. Hou, Adv. Mater., 2015, 27, 4655–4660. DOI: 10.1002/adma.201502110
  7. J. Yuan, Y. Zhang, L. Zhou, G. Zhang, H.-L. Yip, T.-K. Lau, X. Lu, C. Zhu, H. Peng, P. A. Johnson, M. Leclerc, Y. Cao, J. Ulanski, Y. Li, Y. Zou, Joule, 2019, 3, 1140–1151. DOI: 10.1016/j.joule.2019.01.004